Upgrade Your Bathroom With An American Standard Bathtub: The Easy Way To Install
What To Know
- Use a screwdriver to loosen and remove the nuts connecting the water supply lines to the bathtub.
- Place the bathtub on the subfloor and use a level to ensure it’s level in all directions.
- Can I install an American Standard bathtub in a corner.
Are you ready to elevate your bathroom with the luxurious comfort of an American Standard bathtub? Whether you’re a seasoned DIY enthusiast or a plumbing novice, this detailed guide will empower you to install your new bathtub with ease and precision.
Preparing for the Installation
Before you begin, gather your tools and materials:
- American Standard bathtub
- Drain assembly
- Overflow drain
- Caulking gun and caulk
- Level
- Screwdriver
- Pliers
- Utility knife
- Measuring tape
- Pencil
Removing the Old Bathtub
1. Disconnect the Water Supply: Turn off the water supply valves under the sink or in the basement. Open the faucets to release any remaining water.
2. Remove the Drain and Overflow: Use pliers to detach the drain assembly and overflow drain from the bathtub.
3. Disconnect the Plumbing: Use a screwdriver to loosen and remove the nuts connecting the water supply lines to the bathtub.
4. Remove the Bathtub: Carefully lift the bathtub out of the bathroom. If it’s heavy, ask for assistance.
Installing the New Bathtub
1. Level the Base: Place the bathtub on the subfloor and use a level to ensure it’s level in all directions. Adjust the leveling feet if necessary.
2. Install the Drain and Overflow: Insert the drain assembly into the drain hole and secure it with a nut. Install the overflow drain in the same manner.
3. Connect the Plumbing: Reattach the water supply lines to the bathtub and tighten the nuts securely.
4. Seal the Drain and Overflow: Apply caulk around the base of the drain assembly and overflow drain to prevent leaks.
5. Set the Bathtub: Carefully lower the bathtub into place and make sure it’s level. Secure it to the framing using screws or bolts.
Finishing Touches
1. Caulk the Bathtub: Apply caulk along the edges of the bathtub where it meets the wall and floor. This will prevent water from leaking behind the bathtub.
2. Install the Trim: If your bathtub has a decorative trim, install it according to the manufacturer’s instructions.
3. Clean Up: Remove any excess caulk and debris from the bathroom.
Troubleshooting Common Issues
- Water Leaking from the Drain: Check if the drain assembly is properly installed and tightened. If it’s loose, tighten it using pliers.
- Water Leaking from the Overflow: Ensure the overflow drain is securely connected to the bathtub and that there are no cracks or damage.
- Bathtub Not Level: Adjust the leveling feet under the bathtub until it’s level in all directions.
- Bathtub Not Secure: Tighten the screws or bolts securing the bathtub to the framing until it’s stable.
Final Thoughts: Bathtub Nirvana Awaits
Congratulations! You’ve successfully installed your American Standard bathtub. Now, soak in the tranquility of your new bathing oasis, knowing that you accomplished this feat with your own hands. Enjoy the ultimate relaxation and comfort that your new bathtub provides.
Top Questions Asked
Q: What type of caulk should I use?
A: Use a high-quality silicone caulk that is specifically designed for bathrooms.
Q: How long should I wait before using the bathtub?
A: Allow the caulk to cure for at least 24 hours before using the bathtub.
Q: Can I install an American Standard bathtub in a corner?
A: Yes, there are specific American Standard bathtubs designed for corner installations.
Q: How do I clean the bathtub?
A: Use a mild bathroom cleaner and a soft cloth. Avoid using abrasive cleaners or scrubbing pads.
Q: What is the warranty on an American Standard bathtub?
A: American Standard bathtubs come with a limited lifetime warranty.
