Revealed: Effortless Steps To Install Everbilt Tub Spout With Diverter For A Seamless Bathroom Upgrade

Are you looking for a detailed guide on how to install an Everbilt tub spout with a diverter? Look no further! This comprehensive blog post will provide you with step-by-step instructions, helpful tips, and troubleshooting advice to ensure a successful installation. Whether you’re a seasoned DIY enthusiast or a novice homeowner, this guide will empower you to tackle this project with confidence. So, gather your tools, read on, and let’s get started!

Tools and Materials Required

Before embarking on the installation process, ensure you have all the necessary tools and materials at hand. Here’s a checklist to help you prepare:

1. Everbilt tub spout with diverter
2. Adjustable wrench
3. Phillips head screwdriver
4. Flat head screwdriver
5. Teflon tape
6. Plumber’s putty
7. Utility knife
8. Safety goggles
9. Gloves

Step-by-Step Installation Guide

1. Turn Off the Water Supply:

• Begin by locating the main water supply valve for your bathroom. Typically, it’s situated under the sink or behind the toilet. Turn the valve clockwise to shut off the water supply completely.

2. Prepare the Tub Spout:

• Remove the aerator from the old tub spout using a wrench.
• Wrap the threads of the new Everbilt tub spout with Teflon tape, ensuring it’s tightly wound in a clockwise direction. This will help create a watertight seal.

3. Remove the Old Tub Spout:

• Use a flat head screwdriver to pry off the old tub spout’s faceplate. Be careful not to damage the surrounding tiles or fixtures.
• Once the faceplate is removed, use an adjustable wrench to loosen and remove the old tub spout.

4. Clean the Installation Area:

• Thoroughly clean the area where the new tub spout will be installed. Remove any dirt, debris, or old sealant using a damp cloth. This will ensure a proper seal.

5. Apply Plumber’s Putty:

• Roll a small amount of plumber’s putty into a rope-like shape. Place the putty around the base of the new tub spout, ensuring it’s evenly distributed. This will help prevent leaks.

6. Install the New Tub Spout:

• Carefully insert the new tub spout into the installation hole. Hand-tighten the tub spout until it’s snug against the wall.
• Use an adjustable wrench to tighten the tub spout further, ensuring it’s securely in place. Be careful not to overtighten, as this could damage the tub spout or surrounding tiles.

7. Attach the Diverter:

• If your Everbilt tub spout came with a diverter, now is the time to attach it. Align the diverter with the appropriate hole on the tub spout and insert it. Secure the diverter by tightening the set screw with a Phillips head screwdriver.

8. Reattach the Faceplate:

• Reattach the faceplate to the tub spout by aligning it with the screw holes. Secure the faceplate using the screws provided.

9. Turn On the Water Supply:

• Slowly turn on the main water supply valve to allow water to flow through the new tub spout. Check for any leaks around the spout or diverter. If you notice any leaks, tighten the connections further or apply additional plumber’s putty as needed.

10. Test the Diverter:

• Operate the diverter to ensure it’s functioning correctly. Switch between the tub spout and showerhead to confirm that water flows smoothly through each outlet.

Troubleshooting Common Issues

1. Leaking Tub Spout:

• If you notice a leak around the tub spout, tighten the connections further or apply additional plumber’s putty to create a better seal.

2. Diverter Not Working Properly:

• If the diverter is not functioning correctly, check to ensure it’s properly installed and that the set screw is tightened securely. You may also need to replace the diverter if it’s damaged or worn out.

3. Low Water Pressure:

• If you experience low water pressure after installing the new tub spout, check for any kinks or obstructions in the supply lines. You may need to clean the aerator or replace the showerhead if they are clogged.

Additional Tips for a Successful Installation

• Always wear safety goggles and gloves when working with plumbing fixtures to protect yourself from potential hazards.
• If you’re unsure about any aspect of the installation process, consult a qualified plumber for assistance.
• Consider hiring a professional plumber if you’re uncomfortable working with plumbing systems or if you encounter complex issues during the installation.

Summary

Congratulations! You have successfully installed your Everbilt tub spout with a diverter. By following these step-by-step instructions and troubleshooting tips, you’ve ensured a leak-free and functional installation. Now, you can enjoy a refreshing shower or a relaxing bath with confidence. Remember, regular maintenance and occasional inspections will help keep your tub spout and diverter in optimal condition for years to come.

Common Questions and Answers

1. Q: How can I prevent leaks around the tub spout?

• A: Ensure the tub spout is properly tightened and that plumber’s putty is applied around the base to create a watertight seal.

2. Q: What should I do if the diverter is not working correctly?

• A: Check to ensure the diverter is properly installed and that the set screw is tightened securely. You may also need to replace the diverter if it’s damaged or worn out.

3. Q: How can I increase water pressure through the tub spout?

• A: Check for any kinks or obstructions in the supply lines. You may also need to clean the aerator or replace the showerhead if they are clogged.