How To Replace A Flush Valve Washer: A Simple Guide
What To Know
- If the toilet still leaks after replacing the flush valve washer, the problem may be with the flush valve seat.
- Replacing a flush valve washer is a simple and inexpensive DIY task that can save you money and keep your toilet in good working order.
- Signs of a worn-out flush valve washer include a leaky toilet, a slow flushing toilet, or a toilet that flushes continuously.
A leaky toilet is not only an annoyance but also a waste of water and money. One of the common causes of a leaky toilet is a worn-out flush valve washer. Replacing the flush valve washer is a simple and inexpensive DIY task that can save you money and keep your toilet in good working order.
Tools and Materials You’ll Need
- Adjustable wrench or pliers
- New flush valve washer
- Screwdriver (optional)
- Rag or towel
Step-by-Step Instructions
1. Turn Off the Water Supply
Locate the water supply valve behind the toilet and turn it clockwise to shut off the water.
2. Flush the Toilet
Flush the toilet to drain the tank. Continue holding down the flush lever until all the water has drained.
3. Disconnect the Water Supply Line
Use an adjustable wrench or pliers to disconnect the water supply line from the fill valve.
4. Remove the Flush Valve Cap
Use a screwdriver or your hands to remove the flush valve cap. This is usually located on top of the flush valve assembly.
5. Remove the Flush Valve Seat
Once the flush valve cap is removed, you will see the flush valve seat. This is a rubber or plastic ring that seals against the flush valve washer. Use your fingers to gently pry the flush valve seat out of place.
6. Inspect the Flush Valve Washer
Inspect the old flush valve washer for any signs of wear or damage. If the washer is cracked, torn, or deformed, it needs to be replaced.
7. Install the New Flush Valve Washer
Place the new flush valve washer over the flush valve seat. Make sure that the washer is seated properly and is not twisted or folded.
8. Reinstall the Flush Valve Seat
Reinsert the flush valve seat into the flush valve assembly. Push it down until it is fully seated.
9. Reinstall the Flush Valve Cap
Screw the flush valve cap back onto the flush valve assembly. Hand-tighten the cap until it is snug.
10. Reconnect the Water Supply Line
Reconnect the water supply line to the fill valve. Use an adjustable wrench or pliers to tighten the connection.
11. Turn On the Water Supply
Turn the water supply valve counterclockwise to turn on the water.
12. Test the Flush Valve
Flush the toilet to test the flush valve. Make sure that there are no leaks and that the toilet flushes properly.
Troubleshooting Tips
- If the toilet still leaks after replacing the flush valve washer, the problem may be with the flush valve seat. Inspect the seat for any damage or wear and replace it if necessary.
- If the toilet flushes slowly, the problem may be with the water supply line. Check the line for any kinks or obstructions and clear them as necessary.
- If the toilet flushes continuously, the problem may be with the fill valve. Replace the fill valve if necessary.
Recommendations
Replacing a flush valve washer is a simple and inexpensive DIY task that can save you money and keep your toilet in good working order. By following the steps outlined in this guide, you can easily replace the flush valve washer and stop a leaky toilet.
Common Questions and Answers
Q: How often should I replace the flush valve washer?
A: It is recommended to replace the flush valve washer every 2-3 years or as needed if you notice any leaks.
Q: What are the signs of a worn-out flush valve washer?
A: Signs of a worn-out flush valve washer include a leaky toilet, a slow flushing toilet, or a toilet that flushes continuously.
Q: Can I use a universal flush valve washer?
A: Yes, you can use a universal flush valve washer in most toilets. However, it is always best to check the manufacturer’s specifications to make sure.